Product Information

Select Grade Floating Timber, Very Hard, Janka Hardness  of 11. Grey Ashy Tone, with a fair brown and yellow hues. Pre-finished with a very tough wear coat. This floor comes with a 20 year domestic structural warranty.

This is a select grade of floating timber floor and uses FSC certified timber for the production of this product. In addition the raw logs used to make this floor have been air dried for 12 months before being processed.
By doing so This avoids the use of harsh chemicals and allows the timber to naturally harden over time. 


PRODUCT SPECIFICATIONS

Name	Spotted Gum
Size	136x14.5/3x1800
Packing Size	2.937m2/pack
Normal price SALE  Price per m²	$96/m2 $70/m2
Normal price per pack of 2.937m² Sale  Price per pack of 2.937m²	$281.95 $205.59
Certification	ISO9001 ,ISO14001

ABOUT THE WARRANTY
This Floating Timber Flooring is covered by a 20 Year Structural Warranty. This warranty covers all types of structural defects such as delamitation,
buckling and twisting. This warranty is not a wear warranty and does not cover surface wear.

If you are not 100% satisfied with any planks prior to installation, just return the carton, with uncut boards, to your place of original purchase along with your
receipt and BASS Flooring will replace it at no cost. Please note that we offer to replace individual boards only and do not offer cash refunds for unused
boards.

IMPORTANT NOTE! This warranty accepts no responsibility for costs incurred when a floor with visible defects has been installed or when a floor has
been installed without correct sub-floor preparation.

Radiant Heat Performance Warranty Exclusions
This Warranty DOES NOT extend its normal Structural Warranty to flooring used in radiant-heated sub floors: i.e. a heating system that uses electrical
mats/wires or water filled pipes that run through the concrete or sleeper subfloor.

• It is especially important that you maintain proper humidity levels in the interior of your home at all times during the year. Run humidifiers and fans as
necessary to maintain normal humidity variations (40-65%).
• Note: Failure to comply with the above guidelines may cause hairline cracks in the finish.

TIMBER Flooring – Installation Guidelines
Inspect material carefully before installation. Any material installed with obvious defects will not be warranted
The Tongue & Groove Plank should be installed as follows:

INSPECTION: Carefully inspect all material before installation. Customer is responsible for maintaining normal humidity conditions (40%-65%) within the
installation location. The manufacturer is not responsible for environmental conditions that cause excessive expansion and/or contraction.
Jobsite conditions:

In area to be installed, temperature and humidity must be brought to normal usage levels at least 72 hours before installation and maintained at those levels
during installation and maintained at those levels after installation. Flooring should be allowed to acclimatize on site at least 48 hours before installation.
Please leave box sealed for acclimation time. Be sure to use a moisture meter to check moisture levels in both the sub-floor and the flooring
material before installation. NOTE: The flooring and wood subfloor must be no more than 4% in difference.

• Wood Dust: Sawing, sanding or machining wood products can produce wood dust, which can cause a flammable or explosive hazard. Wood
dust may cause lung, upper respiratory tract, and eye and skin irritation. Some wood species may cause dermatitis and/or allergic respiratory
effects. The International Agency for Research on Cancer (IARC) has classified wood dust as a nasal carcinogen in humans. The National Toxicology Program (NTP) has also classified wood dust as a known human carcinogen.
· Avoid dust contact with ignition source.
· Sweep or vacuum dust for recovery or disposal.
· Avoid prolonged or repeated breathing wood dust in air.
Approved respirators may be needed depending upon dust conditions.
· Avoid dust contact with eyes and skin. Wear gloves and safety glasses when handing and machining the product.
· FIRST AID: If inhaled, remove to fresh air. If irritation persists, contact a physician.

• Applications: May be stapled, nailed or glued down over wood sub floors or glued directly to concrete sub-floors, on grade or above grade, we
do not recommend below grade applications. For all types of installation, end joints must be staggered at least 10" to 12"".
Manufacturer recommends installing the flooring perpendicular to the floor joist.
NOTE: Manufacturer does not recommend installing over or onto particleboard, (OSB is the only exception).

• Humidity:"Normal living conditions" are defined as having the relative humidity (air) being monitored and maintained at 40% to 65%,and the
moisture content of the flooring at 6% to 9%,with a tolerance of +/-1%.The proper use of a humidifier/de-humidifier is recommended. Wood that
is too dry may "crack" or "check". Wood that is too damp will increase in width causing "cupping' or crowning".
A moisture content that is too high may also lead to mildew in extreme conditions. These situations are job site related and not considered a manufacturing
defect.

Abuse or Misuse. This warranty does not cover indentations, scratch damages caused by negligence or damage caused by high heel shoes, furniture of
equipment, pet claws, pebbles or sand.
Insect Infestation. This warranty does not cover any insect